Title

Home
Articles Search
clutch kit

Articles search results for clutch kit

Showing 1 to 19 of 19 articles

Brakes - Fitting Discs and Required Ancillaries

What you actually need for the disc/drum conversion is pretty straightforward. Disconnect the steering arms, top and bottom swivel-pins, CV joint, and flexible brake pipes at the subframe - that’s it. There are, however, a number of ancillaries to consider.

Basics

Basics Fitting discs designed for the Mini is easy enough. Just make sure you use CV gaiters for the disc-brake set-up - these have a different bellows shape to stop the gaiter rubbing the inside of the hub. The drum type will rub, then split, shedding grease all over the place. Moly grease is mighty mucky stuff to deal with and doesn't assist braking at all! A tip for racers - to stop the gaiters over-expanding when getting very hot and imitating the aforementioned, put either a decent sized split pin or (my favorite) a piece of very small bore pipe - as in the type supplied with WD40 aerosols, etc. - under the retaining strap on the drive shaft. This allows air to escape and return,

Brakes - Fundamental Considerations

When looking to increase their cars performance, most folks immediately turn to considering higher engine power outputs. Because of this pre-occupation brakes tend to slide down the improvements priority list. However, they are far more important - being able to accelerate at warp speed to hyper-space in the twinkling of an eye is all very well, but disastrous if you can’t stop. You will make a very big hole in the scenery, and possibly end up wearing an wooden over-coat. Getting the braking system sorted out can help to make the car quicker, as you will be able to more confidently, therefore maximising speed in any given situation. Being one of those ‘sciences’ used in the automotive industry I hope to shed some light on the subject as it's another of those where many questions from confused and mislead folks that clog up my e-mail board. The advent of the Metro, and the brakes used on it has spawned a lot of activity in this direction. It was soon discovered that they could b

Flywheel - Pre-Verto Types

The early spring-type clutch flywheels are of no use except where total originality is required on a concours car. The taper is too small and diaphragm pressure ring non-existent. No use to man nor beast. Part No Applications: C-AEG421, C-AEG420, C-AEG619, C-AEG620, 2A3657, 2A3658, 2A3659, 2A3512 With the exception of the fact the two-piece flywheel is two pieces bolted together - this and the later one-piece cast item can be treated as the same thing. They will universally fit all transverse engine cranks from 1964 onwards, so that should be easy enough. If all you can get is the hulking great 1300 type, then this too is as universal to fit, but I highly recommend you get that extra cast lump machined off of the outer edge as a bare minimum. Further lightening of these cast flywheels is possible by having metal machined off of the diaphragm side, from the outer edge of the diaphragm pressure ring outwards.

GEARBOX - How they work

Having decided on or even implemented a course of action to bolster the performance of your Mini’s engine, maximising it’s potential should encompass a good look at the gearbox.

GEARBOX - How they work

Having decided on or even implemented a course of action to bolster the performance of your Mini’s engine, maximising it’s potential should encompass a good look at the gearbox.

Reduction of rotating mass releases more power to accelerate the car as the engine sees less weight to accelerate. Considering for a Mini that a mere 1lb reduction in the rotating mass of the flywheel causes a loss of accelerative weight to the tune of around 12lb - the benefits of rotating mass reduction are obvious. The C-AEG423 weighs some 4lbs less than the standard item.

To extend it's range of superior quality, light-weight steel flywheels, Mini Spares has produced this component to give the later model, SPi Mini owner the benefits from such weight saving. This component has the flywheel sensor reluctor ring machined into the flywheel itself. However, it is NOT compatible with the standard injection diaphragm/spring.

Broken Engine Steady?

Every Mini owner at some point will have an issue with a broken bolt or a stripped thread, due to the fine thread on the majority of bolts fitted to these cars. Whilst most are an easy repair, such as bumper bolts, others can be a lot more difficult to repair.

An ideal example of this is the bolt for the ....

Post race check after Donnington revealed – well, nothing really. Except I still have oil coming from somewhere to give a fine rust-proof coating to the area adjacent to the Clutch housing. Seriously annoying as generally I don't build leaky engines. No leaks from the calipers – so that's a relief, although I am still lacking confidence in the brakes on the whole. I am more and more coming to the conclusion that it is the pad type....

It was time to strip both front brake calipers completely and re-seal them to stop the irritating leaks. So that's exactly what I did using the new sets of seals I bought from KAD instead of the standard AP Lockheed seals. The AP ones look fine, but obviously something is causing them to relax or deteriorate in race use. With the calipers re-built and re-fitted I bled the system up with my Gunsons Easi-Bleed one-man brake bleeding kit.

It seemed pointless fitting new pads in for one race as I had plans to up-grade the brakes over the winter which would include a new set of a different type. I then decided to try and track down where the damned oil was coming from that was on the inner wing and under the clutch....

Borg & Beck by Firstline

Borg & Beck is a name synonymous around the world with high quality clutches.

Recently, an American website had the following text.

Over the past few years some company’s are claiming to be selling Borg & Beck clutch kits and pieces. These are not boxed Borg & Beck.

Our customers car is a 1962 Austin Mini, which originally cost £250.00 and now looks absolutely standard and truly immaculate. Only when you look inside do you realise it is a car with a difference. Richard has already restored two Coopers to a very high standard and his criterior on the Twini was to use as many secondhand production car parts as possible to keep the cost down.

In 1988, a humble 1973 Mini 1000 was minding its own business somewhere in London, when along came a young Mini freak called Jason King, who wanted to change it for ever, and make it famous.

Jason persuaded the owner to take £450 for the car, and then proceeded to throw £12,000 worth of presents at it for the next 3 years. Every minute of Jason’s spare time was spent working on his new car and every minute of his working time was spent looking for spares.

Mini Spares - 8-Port Project Min If you refer back to the October 1993 edition of Mini Tech News, we were about to embark on modifying the suspension. As luck would or would not have it, we had the advantage of setting up and sorting out the Monte Carlo Mini, which would help us in some directions. After checking the ride height of the car, it was higher on the left hand side by 1 Vs' at the front and W' at the back.

Nervous Breakdown Sometime ago in an issue long, long ago in a Calver's Clinic, I did a short piece on vented or grooved discs, with a promise to look at brakes a little closer at a later date.

Engineering Success
A little bit about us, and what we are about! Mini Spares Centre Ltd is the holding company for the following companies:- Competition Silencers International Ltd Minilife Ltd Special Tuning Ltd Leyland Special Tuning Ltd Special Tuning Abingdon Ltd Mini Spares Ltd Network Hardware Ltd Mini Spares Ltd, the engineering division, holds BS5750 approval IS09002, but most of our turned machined products are subcontracted out to specialists. ie. Gears....

Donny Focus - BigMacRacing

Oulton Park was utterly frustrating – there were big hopes returning to a fantastic circuit the Mini 7 Club last visited in 2012. The Cheshire circuit really is a fantastic location, providing race driver a superb challenge...

Articles search results for clutch kit

Contact Mini Spares

Store Details:

Classic Mini Brochure & Manuals